KCS057QV1AA-G03 Replacement — 5.7″ 320x240
| Original specification — KCS057QV1AA-G03 | Published industry specification for the original Kyocera part, compiled from supplier catalogue data. |
|---|---|
| Display Size | 5.7 inch (—) |
| Resolution | 320x240 |
| Original Manufacturer | Kyocera |
| Original Interface | Parallel |
| Outline Dim. (mm) | 154.6 x 114.8 mm |
| Original Backlight | CCFL |
| Replacement Class | CUSTOM — no catalogue equivalent; built against your original outline |
| RONEN Catalogue Module | No off-the-shelf equivalent — custom build against the original outline |
| Fit Notes | CSTN family; source: archive site, spec unverified |
| Supply Model | built to order — custom programme, no broker stock |
Engineering notes — what changes when you re-source a discontinued 5.7 panel
The four points below are what an engineering review actually checks on a re-sourced 320x240 module — read them before you request a quotation.
Why sourcing from the broker market is the expensive route
Discontinued Kyocera parts surface on the broker market at wide price spreads, mixed production dates and no vendor warranty. A last-time-buy batch also caps programme volume: once it is gone, the line stops. Rebuilding the module from the published specification removes both risks, because the 320x240 format stays in production for as long as your programme needs it.
What we rebuild, and what can be upgraded
The replacement follows the original 320x240 outline, active area and resolution so the enclosure and frame buffer stay untouched. Backlight, driver IC, interface, touch and temperature range are re-selected around it: an IPS upgrade for viewing angle, a high-brightness backlight for semi-outdoor use, wide-temperature components for cold starts, or CTP where the original had none.
How fit is confirmed before you commit
Send the original datasheet, a drawing, or the panel itself. Engineering checks outline, connector position, timing and backlight against your board and reports which parameters match and which do not, including anything that cannot be matched exactly. You approve a sample before any volume order, so no tooling is committed on paper alone.
Programme terms that matter for a re-sourced part
Re-sourced programmes run on the same terms as our standard catalogue: sample first, engineering support through bring-up, and volume scheduling that follows your build plan. Lead time is set by glass cutting and backlight selection for the 320x240 format, not by warehouse picking. If the original part is still cheaper in small quantities, we say so — the custom route wins on continuity, not on unit price.
Frequently asked questions — KCS057QV1AA-G03 replacement
Is there an off-the-shelf replacement for KCS057QV1AA-G03?
Not as a stocked catalogue item. Kyocera panels in this class were built to order at the original maker as well: glass is cut to the 320x240 format and the backlight is selected per programme, so nothing sits in a warehouse waiting for a buyer. What we do offer is the module built against your specification, with engineering confirming the fit before any tooling is committed.
What does the replacement match, and what does it change?
The published specification is the starting point: 5.7 inch 320x240 from Kyocera. no catalogue module covers this part, so the route is a custom build against the original outline and connector definition. Backlight, driver IC, interface option, touch and temperature range are re-selected around that core, and the compatibility review states plainly which parameters match the original and which require your confirmation.
Can you match the original brightness and temperature range?
Where the original maker published a value, we build to it. Where no value was published, brightness and temperature are set from your sample or your operating envelope, including high-brightness backlights for semi-outdoor 5.7 use and wide-temperature component selection for cold-start equipment.
What if the original KCS057QV1AA-G03 drawing is lost?
Send a physical sample instead. We measure outline, active area, connector position and pinout, and rebuild the module from measurements. This is the common case for industrial HMIs, machine interfaces, POS terminals and building access panels designs where the original documentation no longer exists.
Is this a verified drop-in replacement?
It is built to the original specification rather than sold as a verified drop-in. Send the datasheet or a sample and engineering confirms outline, connector, timing and backlight against your board, telling you exactly which parameters match and which do not. That assessment is what you use to decide whether the substitution suits the application.
How long does a replacement programme take?
Because these modules are built to order, lead time is set by glass supply and backlight selection for the 320x240 format rather than by stock availability. The sequence is engineering review against your specification or sample, sample build and your bring-up, then volume scheduling to your production plan. The realistic glass-supply date is confirmed during the review instead of quoting a generic figure.
Related discontinued-panel replacements
Other discontinued panels we rebuild to specification: Compatible LCD Replacements (hub) · KCS057QV1AJ · KCS3224ASTT-X2 · TX14D16VM1CBC · LQ057Q3DC03 · TX14D23VM5BPA · TX14D12VM1CBC
Send the original specification
Email the datasheet, drawing or photos of your KCS057QV1AA-G03 panel to sales@odmlcd.com — engineering replies with a match assessment before you commit to tooling.
Email Engineering